Skip to content
Shell & tube heat exchanger specialists

Heat transfer, engineered end to end.

Shell & tube heat exchangers of every TEMA type are a core Steelcon product — thermally designed and rated with HTRI, mechanically designed to TEMA and ASME Section VIII, and built with the tube-to-tube-sheet, expansion and testing disciplines that exchangers demand. From a single condenser to multi-tubular reactors with thousands of tubes, in carbon steel, stainless, duplex, nickel alloys or clad construction.

Send your exchanger datasheet What to tell us
~1,000 m²
Largest heat exchanger
8,800 tubes
3.5 m diameter multi-tubular reactor
178 m²
Duplex exchangers (14 to 178 m² series)
18.5 m²
Explosion-bonded C-2000 clad exchanger

Figures are references from exchangers already supplied, not limits — larger areas, higher pressures and other configurations are engineered to suit each project.

Thermal to mechanical, under one roof

01

Thermal design & rating

Thermal design and rating with HTRI for single-phase, condensing and boiling duties — pressure drop, vibration and fouling checks included — from your process data or your licensor's datasheet.

02

Mechanical design

TEMA Classes B, C and R and ASME Section VIII; tube-sheets, flanges, expansion joints and supports calculated and verified in PV Elite and COMPRESS; nozzle loads and transport checked.

03

Materials

Carbon and low-alloy steels, stainless, duplex and super-duplex, Inconel, Hastelloy and other nickel alloys; explosion-bonded clad tube-sheets and channels; plain, corrugated or finned tubes.

04

Fabrication

Tube-to-tube-sheet joints strength- or seal-welded and expanded with in-house expanders; U-bends heat-treated after trials on samples for each radius; baffle cages, tie-rods and impingement plates built to drawing.

05

Testing & documentation

Shell-side and tube-side hydro tests held for one hour; pneumatic checks before expansion; PMI on all non-carbon-steel parts; IBR-approved for exchangers; full dossier with the equipment.

06

Exchangers in service

Re-tubing, bundle replacement, tube plugging, re-rating and repairs under our National Board R certificate — for exchangers from our works or from elsewhere.

Illustration, not to scale

Inside a shell & tube exchanger

Heat transfer, engineered end to end.

Shell & tube heat exchangers of every TEMA type are a core Steelcon product, thermally designed and rated with HTRI and mechanically designed to TEMA and ASME Section VIII.

Scroll to open it up.

General arrangement01 / 05

1Shell
TEMA shells E, F, G, H, J, K and X.
2Rear head
TEMA rear heads L, M, N, P, S, T, U and W.
3Supports
Tube-sheets, flanges, expansion joints and supports calculated and verified; nozzle loads and transport checked.

Tube bundle02 / 05

4Tubes
Plain, corrugated or finned; triangular, rotated-triangular, square or rotated-square pitch; one to multiple passes.
5Baffles
Single-, double- and triple-segmental and disc-and-doughnut baffles; baffle cages, tie-rods and impingement plates built to drawing.

Two streams03 / 05

Two streams, one duty.

Both sides are thermally designed and rated with HTRI; the mechanical design follows TEMA and ASME Section VIII.

  • Shell side, weaving across the baffles
  • Tube side, out through one pass and back through the other

Opened up04 / 05

6Front head
TEMA front heads A, B, C, N and D.
7Tube-sheets
Tube-to-tube-sheet joints strength- or seal-welded and expanded with in-house expanders.

The whole exchanger05 / 05

Thermal to mechanical, under one roof.

Shell-side and tube-side hydro tests held for one hour, PMI on all non-carbon-steel parts, and a full dossier with the equipment.

Every TEMA type, built to the tube

Fixed tube-sheet
BEM / NEN — with expansion joints where the design needs them
U-tube
BEU / AEU — removable bundles for high-pressure and clean tube-side fluids
Floating head
AES / BES / AET — pull-through and split-ring designs for fouling services
Kettle reboilers
AKT / BKU — vapour disengagement space and weir designed for the duty
Condensers & reboilers
Vertical and horizontal condensers, vent condensers, thermosyphon and forced-circulation reboilers
Evaporator calandrias
Multiple-effect evaporator calandrias and column-mounted exchangers
Multi-tubular reactors
Formaldehyde and catalytic tubular reactors — to 3.5 m diameter and 8,800 tubes
Double-pipe & coil
Double-pipe and hairpin exchangers; internal, limpet and outside coils
Row of shell and tube exchangers with tube sheets
Exchanger bundles ready for dispatch
Column with built-in exchanger
Column with built-in exchanger
Tube sheet close-up
Tube sheet before expansion

Configurations

TEMA designation
Front heads A, B, C, N, D · shells E, F, G, H, J, K, X · rear heads L, M, N, P, S, T, U, W
Tubes
Plain, corrugated or finned · triangular, rotated-triangular, square or rotated-square pitch · one to multiple passes
Baffles
Single-, double- and triple-segmental and disc-and-doughnut baffles
Expansion joints
Thin-wall bellows (plain or reinforced), flexible shell elements, toroidal bellows
Codes & classes
ASME Section VIII Div. 1 and 2, PED, IBR 1950; TEMA Classes B, C and R; stamping where required

Reference exchangers

  • Shell & tube heat exchanger of about 1,000 m²
  • Duplex exchangers — 13.5, 45.8, 84.7, 104.5, 174.5 and 177.5 m²
  • Inconel 600 exchangers (E-102 A/B/C, E-202 A/B) and gas-phase reactors
  • 18.5 m² explosion-bonded SS 304 + C-2000 exchanger
  • Duplex MEE second-effect calandria, 30 m²
  • Duplex U-tube condenser, 11.7 m²; CS / SS 316L horizontal exchangers
  • Multi-tubular reactors — 3.5 m diameter, 8,800 tubes
  • Jacketed regenerators and recovery columns with built-in heat-transfer sections

What to tell us about your duty

A thermal datasheet is ideal. If you are starting from the process, these points let our engineers propose a design in the first reply.

The duty Fluids on each side, flow rates, inlet and outlet temperatures, allowable pressure drops, fouling factors — or simply the process datasheet.
Design data Design and operating pressure and temperature for each side, TEMA class, construction code and stamping requirement.
The geometry TEMA type, tube OD and count if known, tube type and pitch, baffle type, shell ID and tube length — or leave the geometry to us.
Materials & finish Shell-side, tube-side, tube and tube-sheet materials; radiography scope; surface finish — or the fluids, and we will propose them.
Send your exchanger datasheet

Related

Heat transfer & separation equipment High & exotic alloys Service & support

No datasheet yet? Enter the design data you have, section by section, and we will work out the rest.

Technical enquiry form